USAGE VIDEO OF OUR 2024 MODEL MACHINE:
  (English subtitle)

USAGE MANUAL OF OUR 2024 MODEL MACHINE:

• OUR SYSTEM PANEL HAS AN ETHERNET MODULE, AND WE CAN TO DETECT OR MODERNIZE FAILURES BY
CONNECTING REMOTELY IN CASE OF AN INTERNET CONNECTION. INTERNET CONNECTION IS POSSIBLE BY
PLUGGING YOUR ETHERNET CABLE TO THE ETHERNET MODULE IN THE ENERGY BOX.
• THE PROCEDURES TO BE TAKEN WHEN ACTIVATING THE SYSTEM ARE LISTED BELOW:

1. CONNECT THE INTERCONNECTION CABLES BETWEEN THE PLATES AND THE ENERGY BOX
ACCORDING TO THE CONNECTION DIAGRAM LOCATED ON THE BACK OF THE ENERGY BOX.

2. CONNECT THE HYDRAULIC MOTOR PUMP ENERGY CABLE.

3. CONNECT YOUR MAIN ENERGY CABLE TO THE 5X125A PLUG THAT WE SENT. AND CONNECT THIS
PLUG TO THE ENERGY BOX MAIN SOCKET.

4. MAKE MAIN PAKO SWITCH TO POSITION 1, TO ENERGYZE THE BOX.

5. FOR RECORDING THE PROCESS, CHECK THAT A USB MEMORY STICK BEHIND THE LCD SCREEN IS IN
PLACE.

6. ON THE PLC SCREEN, ENTER TO THE “TIMP MENU” AND THE GREEN COLOR BARS. SET THE COOKING
TIME ACCORDING TO YOUR DESIRE FOR EACH PLATE SEPERATELY. ITS SET TO 60 MINUTES AS
FACTORY SETTING.
(COOKING TIME MEANS: LETS SUPPOSE OUR TARGET TEMPERATURE IS 145 DEGREE. SO, COOKING
TIME MEANS HOW MANY MINUTES WILL THE PLATES REMAIN AT 145 DEGREES AFTER REACHİNG
145 DEGREES.)

7. AGAIN ON THE TIMP MENU THE PINK BARS MUST BE ZERO AT THE BEGINING. PINK BARS SHOWS
HOW MANY MINUTES PLATES COOKED. WHEN THE PINK BAR TIME VALUE EQUALS TO THE COOKING
TIME VALUE, THEN VULCANIZATION WILL END. THE SYSTEM SHUTS DOWN ITSELF AUTOMATICALLY.
AT THE BEGINING OF THE OPERATION MAKE SURE PINK BARS ARE ALL SET TO ZERO. IF NOT, PUSH
RESET BUTTONS TO MAKE THEM ZERO. (RESET BUTTONS ARE PHYSICAL BUTTONS ARE AT THE MOST
BOTTOM OF PANEL.)

8. ON THE PLC SCREEN, ENTER TO THE “CONTROLUL TEMPERATURIAL” MENU. AND SET TARGET
TEMPERATURE FROM GREEN BARS. ITS SET TO 145 DEGREE AS FACTORY SETTING.

9. YOU CAN START THE HEATING PROCESS OF THE SYSTEM BY TURNING RIGTH THE 6(SIX) PHYSICAL
SWITCHES LOCATED ON THE FRONT OF THE PANEL TO POSITION 1. (PLEASE ASK FOR SUPPORT TO
INTERFERE WITH THE SETTINGS ON THE HYSTERESIS AND PROPORTIONAL OUTPUT PAGES.)

10. THE HYDRAULIC UNIT:

10.1 PRESS THE MOTOR-PUMP BUTTON ON THE PLC SCREEN, THEN TURN THE MAIN POWER
SWITCH RIGTH WHİCH İS ON THE HYDRAULIC MOTOR PUMP, THE ENGINE WILL START.

10.2 WHEN THE PRESSURE REACHES 200 BAR, YOU WILL CLOSE THE BALL VALVE ON HYDRAULIC
MOTOR PUMP. (TO KEEP CONSTANT THE PRESSURE.)

10.3 AT THE END OF VULCANIZING, OPEN THE BALL VALVE. (TO DECOMPRESS THE PRESSURE,
STEP 1)

10.4 TURN THE MINI PACO SWITCH TO POSITION 1 WHICH IS ON THE HYDRAULIC MOTOR PUMP.
(TO DECOMPRESS THE PRESSURE, STEP 2)

11. YOU CAN WATCH THE REACTIONS SHOWED BY THE TEMPERATURES ON THE “GRAFIC” PAGE.

12. YOU CAN SEE BOTH THE CENTER AND EDGE(LATERAL) TEMPERATURES IN THE PLATES FROM THE
“ECRAN DE CALDURA” PAGE.

13. START THE DISASSEMBLY PROCESS AFTER THE PLATES TEMPERATURES DROPPED BELOW 60
DEGREES.